Samsung smiley T359 Hard Reset Procedure

Here's a step by step instruction on how to factory reset and restore the Samsung Smiley T359 to it original default settings.

Note: Do a back-up copy of all your installed data on the device for it will be wipe out in this process. 

To reset the phone through menu settings:

1. From the Main Home screen, Press menu
2. Select Settings
3. Select Reset Settings
4. A highlight option and highlight All will be presented, you may choose by using the red button to mark the selection.
5. Select and Press Reset
6. Enter the password if prompted, the default is 1234
7. Then confirm

or use this method: type*2767*3855#

Read More

Samsung Galaxy TAB GT-P1000 Hard Reset Procedure

FORMATTING CODE

Here's the instructions on how to hard reset the Samsung Galaxy TAB GT-P1000. Please do have a back-up copy all of the important documents stored on the device, it will be all deleted including any 3rd-party applications installed on it. 

Resetting the device through Home Screen, this may hrlp to fix if the phone experience some hangs up or freezing if opening some applications.
Samsung Galaxy TAB GT-P1000 Hard Reset
To reset the phone:
1. Select Settings
2. Select Privacy
3. Select Factory Data Reset
4. Then select Reset Tablet

If the Samsung Galaxy TAB GT-P1000 is frozen or unresponsive, you can do hard reset through button key combination.

To hard reset:
1. Turn the  Samsung Galaxy TAB GT-P1000 Power OFF
2. Press and Hold the Volume Down and Briefly press the Power button.
3.Release the Power button button when the Samasung logo appears.
4. An additional menu will appear, just follow the whole instruction to hard reset the device.

The device will then reboot, after this process been done and back to its original factory default settings.

Read More

posts Blackberry bold 9000 keypad ways solutions

This morning I shared trick jumpers to problems keypad on blackberry bold 9000, probably from one of the readers of this blog, is currently experiencing problems the keypad on the blackberry bold 9000, on a phone keypad damage usually occurs on hardware factors, there are some phones have a problem of damage keypad is caused by software, but it was only a few phones and not all of them caused by damage to the software and not all of them caused by hardware, but this time that I share is the destruction of the keypad on the blackberry bold 9000 caused by hardware, ie, if there is one lane keypad the end, you can do with jumpers according that you see in the image above

Read More

Nokia C1-01 Charging Solution

Nokia C1-01 Charging Solution

Read More

Nokia 1208 Blue display solutions

noki phone in 1208, is a class of low-end phones, and this ponssel often experience some problems, especially damage to hardware, from local damage mode, the lights went out, even to damage to the screen, which looks blue screen, there are various ways to repair every cell phone, but not yet certainly damage can be overcome in the same way, although having the same type of damage

well for that, am I here want to share to you about how to repair nokia 1208 cell phone were damaged, blue display. I do it? try you noticed the image above

Read More

nokia 7230 full solution

Nokia 7230 Charging, Mic, Speaker, MMC, Network, Signal, Jumper Ways Solution download

Read More

How to Check Basic Electronic Components Using a Multi-Meter 

Basic electronic components such as resistors, capacitors, diodes and transistors are widely used in any electronic devices and gadgets. Knowing how to conduct a test on this components using a multimeter would give you an idea on how to trouble shoot and repair any defective cellphones or electronic equipments at home. Below are some basic D.I.Y. regarding proper testing of this components using a multimeter.

How to Check Resistors?

Read the indicated  code value indicated in Schematic Diagram then select the Ohm-scale within but not way below the indicated value. A resistor is good if its resistance is close to the indicated value.Tolerance should be considered with the ohmmeter reading. While, no resistance reading at all on the ohmmeter scale settings means that the resistor is open. A zero resistance reading on all ohmmeter scale settings means that the resistor is shorted. 

How to Check Capacitors?

In most cases, a capacitor fails due to the deterioration of the dielectric material between its plate.Defective capacitors can have an internal shorted terminals, excessive leakage and degradation of capacitance meter. For an electrolytic capacitor (capacitors with polarity), short the terminal capacitor to discharge it prior to testing.

To test a capacitor, set the multimeter to Rx10 or Rx1K scale. Connect the tester negative probe to the capacitor positive terminal and the positive probe to the negative terminal. 

A good indication for electrolytic capacitor shows the meter needle deflecting towards zero and moves back again to infinite resistance position. 
For ceramic, Mylar and other capacitor with a capacitance with less than 1.0 uF, the meter will not deflect at all. 

A defective indication for an electrolytic capacitor shows that the meter will rest on zero and remain stationary at a point which is an indication that the capacitor is shorted.

How to Check Diodes?

Set the multimeter knob to any of the resistance position (x1, x10, x1K or 10K ohm ).Connect the positive probe to the anode and the negative probe to the cathode.Then connect the positive probe to the cathode and the
negative probe to the anode of the diode. A good indication in the first procedure will show the meter deflected very little or may not deflect at all.

And in the second procedure, the meter will deflect towards zero.The actual resistance reading is the forward resistance of the diode. 

A defective indication shows that the meter won't deflect at all even when the probes are reversed. Or the meter deflects at the same time or almost the same resistance reading for both steps.

How to Check Transistors:

Bipolar transistors are usually checked out of a circuit by means of an ohmmeter. When it is desired to check for the resistance across the transistor emitter and collector, NPN or PNP, ohmmeter probes may be connected either way. A good transistor will show above a reading above 1000 ohm.

How to determine if it is NPN or PNP transistor?

To determine the correct terminal of the transistors, set the range selector to x 1 or 10 ohm.Connect the positive probe to the emitter and the negative probe to the base of the transistor. Note the reading interchange the connection of the probes to the leads of the transistor.

Base your conclusion on the table:

POSITIVE PROBE TO: -----NEGATIVE PROBE TO: -----RESISTANCE READING-- CONCLUSION:
  Emitter------- --   Base---------- Less than 150 ohm ------Transistor is NPN
 Base --------------Emitter --------Infinity ----------------Transistor is NPN


POSITIVE PROBE TO:  NEGATIVE PROBE TO:   RESISTANCE READING:    CONCLUSION:  
-Emitter------------Base ---------Infinity   ----------------  Transistor is PNP
Base --------------- Emitter --- - Less than 150 ohm -------  Transistor is PNP

Some defective indications of transistors: Resistance between any pair of the terminals is less than 10 ohms, means that the transistor is shorted. Resistance between base and emitter or base collector for both the forward and reverse application of ohmmeter probes is infinity (meter needle don't deflect), means that the transistor is open. Transistors overheats (except power transistors) during normal operating condition means that the transistor is shorted.

 How to Check an LED ( Light Emitting Diode)

Set the Muti-meter to x1 connect the positive probe to cathode and the negative probe to anode. The good and working LED will then light up or glow, a busted LED will not.

How to Check a Coil?

Set the multimeter to X1 a good and working coil have a reading approximately point to zero ohms, without any reading means the coil is open or busted.

How to Check a Fuse?

A blown SMD Fuse is not visible to our naked eye, just set the multi-meter to x1 and put both test probe to both end side of the fuse. A full reading here to zero or continuity check is full. without any reading means the fuse is already busted.

How to Check IC chips (Integrated Circuits)?

IC Chips is hard to determine faulty by using only a multi-meter, some advance equipment like the one that the manufacturer used during their productions. However; you can determine a faulty chips by some few experiences when it comes to troubleshooting, One techniques is that by comparing two same components from one another. like for example; if one chips is suspected to be faulty, then by replacing it with a good and working same chips, you can now determine it if the said chips got a problem. It is a trial and error method at first; but as long as your experience and knowledge skills increases, you can determine it more quickly and accurately.
Further, we will tackle this issues and give you some tips and tricks.

Read More